3D Printer Cartridges
3D Printer Cartridges
-
Monoprice 111779 PLA 3D Printer Filament - Pink - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 111779$27.60Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice PLA 3D Printer Filament - Red - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 110553$22.12Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice PLA 3D Printer Filament - Grey - 1kg Spool 1.75mm Thick | for All PLA Compatible Printers 111778$36.52Get outstanding 3D printing results when you use 1.75mm PLA 3D printer filament from Monoprice! Pla is a good choice for a printing material If you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). thickness and roundness factors are laser measured at the Factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice PLA 3D Printer Filament - Gold - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 112299$34.99Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice PLA 3D Printer Filament - Glow In The Dark Green - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 111780$29.56Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice PLA 3D Printer Filament - Fluorescent Purple - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 111552$27.60Out of stockGet outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice 111551 PLA 3D Printer Filament - Crystal - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 111551$34.99Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice PLA 3D Printer Filament - Blue - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 111043$20.59Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice PLA 3D Printer Filament - Black - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 110551$20.59Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice 114376 PLA 3D Printer Filament - Natural - 0.5kg Spool 1.75mm Thick | | For All PLA Compatible Printers 114376$11.89Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 0.5 kg spool features a thickness of 1.75mm ±0.05mm. It has a nominal processing temperature of 180 ~ 210°C (356 ~ 410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice PLA 3D Printer Filament - Light Blue - 0.5kg Spool 1.75mm Thick | | For All PLA Compatible Printers 114380$15.70 $15.70Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 0.5 kg spool features a thickness of 1.75mm ±0.05mm. It has a nominal processing temperature of 180 ~ 210°C (356 ~ 410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More