Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D printer filament from Monoprice! Pla is a good choice for a printing material If you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). thickness and roundness factors are laser measured at the Factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 0.5 kg spool features a thickness of 1.75mm ±0.05mm. It has a nominal processing temperature of 180 ~ 210°C (356 ~ 410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 0.5 kg spool features a thickness of 1.75mm ±0.05mm. It has a nominal processing temperature of 180 ~ 210°C (356 ~ 410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
Overview: SainSmart TPU filament is renowned for its high strength and flexibility. With the design freedom of 3D printing, SainSmart filament is the key to bringing your project, whether it be a weekend hobby or prototyping for a Fortune 500 company, from the sketchpad to reality. Each spool of SainSmart TPU filament comes with 0. 8 kg/1. 76 lb. of material. This filament is drawn out to a diameter of 1. 75 mm with a dimensional accuracy of +/- 0. 05 mm, making it the perfect choice for most printers on the market. Specification: Diameter: 1. 75 mm Material: Flexible TPU Net Weight: 0. 8 kg Shore Hardness: 95 A Recommended Printer Settings Print Nozzle: 0. 4 – 0. 8 mm Extruder Temperature: 195 – 230°C Print Bed Temperature: 40 – 60°C Cooling Fan: On Printing Tips For Bowden Drive Printers Print Slower: 15 – 30 m/s First Layer Settings: 100% Height. 150% Width, 50% Speed Disable Retraction: Should reduce oozing and stringing Cooling Fan: On after first layer Increase Multiplier: 1. 1, should increase bonding Do not over extrude filament when loading. As soon as the filament start protruding from the nozzle, stop. Loading any faster will cause the filament to get caught in extruder gear. Feed the filament directly to the extruder, and not through the feeder tube. This reduces back tension in the filament as well as drag, ensuring proper feeding. What’s in The Package 1x SainSmart TPU Flexible Filament 1. 75mm 0. 8kg vacuum sealed w/ desiccant Learn More
Overview: TPU filament is renowned for its high strength and flexibility. With the design freedom of 3D printing, filament is the key to bringing your project, whether it be a weekend hobby or prototyping for a Fortune 500 company, from the sketchpad to reality. Each spool of TPU filament comes with 0.8 kg/1.76 lb. of material. This filament is drawn out to a diameter of 1.75 mm with a dimensional accuracy of +/- 0.05 mm, making it the perfect choice for most printers on the market. Specification: Diameter: 1.75 mm Material: Flexible TPU Net Weight: 0.8 kg Shore Hardness: 95 A Recommended Printer Settings Print Nozzle: 0.4 – 0.8 mm Extruder Temperature: 195 – 230°C Print Bed Temperature: 40 – 60°C Cooling Fan: On Printing Tips For Bowden Drive Printers Print Slower: 15 – 30 m/s First Layer Settings: 100% Height. 150% Width, 50% Speed Disable Retraction: Should reduce oozing and stringing Cooling Fan: On after first layer Increase Multiplier: 1.1, should increase bonding Do not over extrude filament when loading. As soon as the filament start protruding from the nozzle, stop. Loading any faster will cause the filament to get caught in extruder gear. Feed the filament directly to the extruder, and not through the feeder tube. This reduces back tension in the filament as well as drag, ensuring proper feeding. What’s in The Package 1x TPU Flexible Filament 1.75mm 0.8kg vacuum sealed w/ desiccant Learn More
Designed for Most FDM 3D Printers. It Supports Diverse FDM 3D Printers in Market Very Well SUNLU Silk PLA Filament Series Brings Arts & Crafts & 3D Projects Smooth Satin Beautiful Surface Do You Like Satin Lovely Silk Shiny Surface in Your Finished 3D Printed Item? If it is, Pls Do Not Hesitate to Choose SUNLU Filament! Learn More
Fast Server Corp is not responsible for data, typographical, or photographic or technical errors. Pricing and availability are subject to change without notice!!!
All trademarks, service marks, product names and logos appearing on this site are the property of their respective owners. Use of them does not imply any affiliation with or endorsement by them.
We can send formal quotes or bids upon request.
Please submit contact form to request a quote.
We accept purchase orders from government and public education entities, as well as publicly traded corporations. CAGE Code: 858P6 | D.U.N.S #: 08-055-2103 | UNGM #: 571579