3D Printer Cartridges
3D Printer Cartridges
-
Dremel Nylon 3D Printer Filament 1.75 mm Diameter Black DF45-NYP-B$34.49Dremel Nylon filament has been specifically engineered for optimal printing with your Digi lab 3D45. Nylon is a thermal plastic that softens and melts when it's heated, building your designs layer by layer. Parts made from Dremel's Nylon are stronger, more flexible and more durable than parts made from traditional PLA. Learn More
-
Monoprice PLA 3D Printer Filament - Grey - 1kg Spool 1.75mm Thick | for All PLA Compatible Printers 111778$36.52Get outstanding 3D printing results when you use 1.75mm PLA 3D printer filament from Monoprice! Pla is a good choice for a printing material If you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). thickness and roundness factors are laser measured at the Factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice PLA 3D Printer Filament - Gold - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 112299$34.99Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
Monoprice 111551 PLA 3D Printer Filament - Crystal - 1kg Spool 1.75mm Thick | | For All PLA Compatible Printers 111551$34.99Get outstanding 3D printing results when you use 1.75mm PLA 3D Printer Filament from Monoprice! PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot. Learn More
-
XYZprinting RFPLCXUS0CH da Vinci Jr. & mini Series Filament PLA 600 g Pearl White RFPLCXUS0CH$39.42XYZprinting presents the non-toxic PLA filament for the da Vinci Jr. & mini Series. This PLA filament is compatible with our da Vinci Jr. & mini series printers which use 1.75mm diameter filament. Each filament has been tested for quality and proven for performance and comes in a 600g spool. Learn More
-
NinjaTek 3DNF00117505 NinjaTek NinjaFlex TPU Filament 1.75mm TPE.5kg Snow (White) (Pack of 1) 3DNF0017505-1$32.50Ninja Flex flexible filament leads the industry thanks to its superior flexibility and longevity compared to non-polyurethane materials. Its consistency in diameter and orality (roundness) outpaces other polyurethane materials. Made from a specially formulated thermoplastic polyurethane (TPU) material, this patented technology boasts a low-tack, easy-to-feed texture. The result is uniquely flexible, strong prints ideal for direct-drive extruders. Suggested Applications: Seals, gaskets, plugs, leveling feet, protective applications. KEY FEATURES: Shore Hardness = 85A Truly flexible (no fill or layer manipulation required to achieve performance) 660% elongation allows for repeated movement and impact without wear or cracking Polyurethane composition allows for excellent vibration reduction Patented low friction exterior allows for smooth feeding Abrasion resistance 20% better than ABS and 68% better than PLA Consistent diameter and material properties providing reliable, high quality prints Chemical resistant to many materials, including naphtha, ASTM Oils #1-3, petroleum and Freon Adheres to all standard build platforms without glue or tape REACH and RoHS 2002/95/EC Directive compliant PRINTING GUIDELINES: Extruder Temperature: 225°C – 235°C Platform Temperature: Room temperature – 40°C Glue and/ or blue painters tape is suggested if not using a heated bed. Print Speed: Top and bottom layers: 10-20 mm/ sec (600-1200 mm/ min) Infill speeds: 15-35 mm/ sec (900-2100 mm/ min) Layer 2+ use cooling fan if available. Learn More
-
MakerBot PLA Filament 1.75 mm Diameter Large Spool Black MP05775 MP05775$48.00 $48.00MakerBot Filament is the best and most consistent filament for MakerBot Replicator 3D Printers. MakerBot PLA Filament is a bioplastic made from corn. All its dyes are FDA-approved as food safe and it is guaranteed to have no heavy metals, phthalates, or BPA. Every filament color is comprehensively quality tested at both 100-micron and 200-micron layer resolutions to verify that the filament will perform every feature that MakerBot MakerWare and MakerBot Desktop software offer. If you are new to 3D printing, MakerBot PLA Filament is a good material to start with because it is easy to use and performs well on most prints. Compatible with the MakerBot Replicator 2, MakerBot Replicator (Fifth Generation), MakerBot Replicator Z18. Glass Temp: 60-65 C (140-149 F) Melting Temp: 150-160 C (302-320 F) Nozzle Temp: 230 C (446 F) Spool Diameter: 9 in Spool Width: 2 in Spool Hub Hole: 2 in Diameter 1.75 mm Net Weight: 2 lbs. Learn More
-
-
MakerBot PLA Filament 1.75 mm Diameter Large Spool Red MP05779$48.00 $48.00MakerBot Filament is the best and most consistent filament for MakerBot Replicator 3D Printers. MakerBot PLA Filament is a bioplastic made from corn. All its dyes are FDA-approved as food safe and it is to have no heavy metals, phthalates, or BPA. Every filament color is comprehensively quality tested at both 100-micron and 200-micron layer resolutions to verify that the filament will perform every feature that MakerBot MakerWare and MakerBot Desktop software offer. If you are new to 3D printing, MakerBot PLA Filament is a good material to start with because it is easy to use and performs well on most prints. Compatible with the MakerBot Replicator 2, MakerBot Replicator (Fifth Generation), MakerBot Replicator Z18. Glass Temp: 60-65 C (140-149 F) Melting Temp: 150-160 C (302-320 F) Nozzle Temp: 230 C (446 F) Spool Diameter: 9 in Spool Width: 2 in Spool Hub Hole: 2 in Diameter 1. 75 mm Net Weight: 2 lbs. Learn More
-
MakerBot PLA Filament 1.75 mm Diameter Large Spool White MP05780 MP05780$56.99 $56.99MakerBot Filament is the best and most consistent filament for MakerBot Replicator 3D Printers. MakerBot PLA Filament is a bioplastic made from corn. All its dyes are FDA-approved as food safe and it is to have no heavy metals, phthalates, or BPA. Every filament color is comprehensively quality tested at both 100-micron and 200-micron layer resolutions to verify that the filament will perform every feature that MakerBot MakerWare and MakerBot Desktop software offer. If you are new to 3D printing, MakerBot PLA Filament is a good material to start with because it is easy to use and performs well on most prints. Compatible with the MakerBot Replicator 2, MakerBot Replicator (Fifth Generation), MakerBot Replicator Z18. Glass Temp: 60-65 C (140-149 F) Melting Temp: 150-160 C (302-320 F) Nozzle Temp: 230 C (446 F) Spool Diameter: 9 in Spool Width: 2 in Spool Hub Hole: 2 in Diameter 1. 75 mm Net Weight: 2 lbs. Learn More